Steam Sterilization – CSSD MCQ Questions and Study Notes

Steam sterilization is the most common, reliable and economical method for heat-stable items. Practice free CSSD MCQ questions on this topic below.

Take the Steam Sterilization practice test All 45 chapters

Learning objectives

Study notes

Saturated steam under pressure kills microorganisms by denaturing proteins. Typical cycles are about 132–135 °C (270–275 °F) for a validated exposure time, or gravity displacement at 121 °C for longer.

Air removal is critical: pre-vacuum sterilizers remove air with vacuum pulses, while gravity cycles displace air downward. Items must be dry after the cycle, cooled, and handled carefully.

Important points

Key terms

Autoclave Pre-vacuum Gravity displacement Wet pack Saturated steam

Practice MCQs on Steam Sterilization

Tap “Show answer” to check each answer and read the explanation. These practice questions are written for learning with AI assistance and may contain mistakes. Please report any error so it can be fixed.

Questions 1 to 10

1. Steam sterilization kills by:

  1. Protein denaturation
  2. Radiation
  3. Drying only
  4. Freezing
Show answer
Answer: A. Protein denaturation
Moist heat denatures proteins.

Report an error in this question

2. Which is a key steam parameter set?

  1. Time, temperature, pressure
  2. Label, sound
  3. Noise, light
  4. Color, weight
Show answer
Answer: A. Time, temperature, pressure
Core parameters.

Report an error in this question

3. Air trapped in a load causes:

  1. Cooling
  2. Better result
  3. Sterilization failure
  4. Faster cycle
Show answer
Answer: C. Sterilization failure
Air blocks steam.

Report an error in this question

4. Pre-vacuum cycles remove air using:

  1. Water
  2. Freezing
  3. Vacuum pulses
  4. Oil
Show answer
Answer: C. Vacuum pulses
Vacuum removes air.

Report an error in this question

5. A wet pack after the cycle should be:

  1. Used
  2. Treated as not sterile
  3. Stored
  4. Rewrapped wet
Show answer
Answer: B. Treated as not sterile
Moisture wicks microbes.

Report an error in this question

6. Common pre-vacuum exposure temperature is about:

  1. 132–135 °C
  2. 70 °C
  3. 20 °C
  4. 50 °C
Show answer
Answer: A. 132–135 °C
Typical range.

Report an error in this question

7. Steam sterilization suits items that are:

  1. Heat and moisture stable
  2. Heat sensitive
  3. Electronic
  4. Plastic that melts
Show answer
Answer: A. Heat and moisture stable
Must tolerate heat.

Report an error in this question

8. Items should cool before handling to:

  1. Save time
  2. Add moisture
  3. Change label
  4. Avoid condensation and contamination
Show answer
Answer: D. Avoid condensation and contamination
Prevents wet packs.

Report an error in this question

9. Overloading the sterilizer can:

  1. Cut time
  2. Cool items
  3. Improve results
  4. Cause air pockets and wet packs
Show answer
Answer: D. Cause air pockets and wet packs
Poor steam circulation.

Report an error in this question

10. Gravity displacement removes air by:

  1. Freezing
  2. Displacing it downward
  3. Fans
  4. Vacuum
Show answer
Answer: B. Displacing it downward
Steam pushes air out drain.

Report an error in this question

Questions 11 to 20

11. A common pre-vacuum steam cycle for wrapped instruments in US practice is:

  1. 300 °F for 1 hour
  2. 150 °F
  3. 212 °F for 2 minutes
  4. 270–275 °F (132–135 °C) for about 4 minutes
Show answer
Answer: D. 270–275 °F (132–135 °C) for about 4 minutes
US practice: follow IFU and validated parameters.

Report an error in this question

12. A gravity displacement cycle for wrapped instruments is commonly:

  1. 340 °F
  2. 212 °F
  3. 250 °F (121 °C) for 30 minutes
  4. 270 °F for 1 minute
Show answer
Answer: C. 250 °F (121 °C) for 30 minutes
US practice: longer time due to air removal.

Report an error in this question

13. Immediate-use steam sterilization (formerly 'flash') should:

  1. Be unlimited
  2. Be limited and used only when necessary
  3. Replace routine sterilization
  4. Be used for convenience
Show answer
Answer: B. Be limited and used only when necessary
US practice: not for routine use or implants.

Report an error in this question

14. A wet pack after sterilization should be:

  1. Dried
  2. Considered contaminated
  3. Stored
  4. Used
Show answer
Answer: B. Considered contaminated
US practice: reprocess.

Report an error in this question

15. Sterilizer load records should be maintained to allow:

  1. Cost cuts
  2. Noise control
  3. Traceability and recall
  4. Faster loading
Show answer
Answer: C. Traceability and recall
US practice: documentation requirement.

Report an error in this question

16. Standard autoclave cycle for wrapped items in many Indian hospitals is:

  1. 80 °C for 10 minutes
  2. 200 °C for 1 hour
  3. 100 °C for 5 minutes
  4. 121 °C at 15 psi for about 30 minutes
Show answer
Answer: D. 121 °C at 15 psi for about 30 minutes
India practice: gravity displacement cycle.

Report an error in this question

17. A pre-vacuum autoclave cycle at 134 °C typically runs for about:

  1. 30 minutes
  2. 1 minute
  3. 3–4 minutes
  4. 3 hours
Show answer
Answer: C. 3–4 minutes
India practice: at about 30 psi.

Report an error in this question

18. Which organism is used as the biological indicator for autoclaves?

  1. Staphylococcus aureus
  2. E. coli
  3. Candida
  4. Geobacillus stearothermophilus
Show answer
Answer: D. Geobacillus stearothermophilus
India practice: standard spore test.

Report an error in this question

19. Autoclave tape shows:

  1. Pack age
  2. Pack weight
  3. That the pack was exposed to steam
  4. That the pack is sterile
Show answer
Answer: C. That the pack was exposed to steam
India practice: process indicator only.

Report an error in this question

20. Wet packs after autoclaving are usually due to:

  1. Correct loading
  2. Long cooling
  3. Good vacuum
  4. Poor drying or overloading
Show answer
Answer: D. Poor drying or overloading
India practice: treat as not sterile.

Report an error in this question

Questions 21 to 30

21. Steam is a preferred sterilant because it is:

  1. Fast, reliable, non-toxic and economical
  2. Slow and toxic
  3. Expensive and weak
  4. Unsafe for metal
Show answer
Answer: A. Fast, reliable, non-toxic and economical
Used whenever the device allows.

Report an error in this question

22. The three main phases of a steam cycle are conditioning, exposure and:

  1. Exhaust and drying
  2. Labeling
  3. Storage
  4. Packing
Show answer
Answer: A. Exhaust and drying
Each phase matters.

Report an error in this question

23. Exposure time is counted from when:

  1. The cycle is selected
  2. The chamber reaches sterilizing temperature
  3. Staff leave
  4. The door closes
Show answer
Answer: B. The chamber reaches sterilizing temperature
Timing starts at set temperature.

Report an error in this question

24. The drying phase removes:

  1. Hardness
  2. Moisture from the load
  3. Bacteria only
  4. Detergent
Show answer
Answer: B. Moisture from the load
Dry loads stay sterile.

Report an error in this question

25. Basins and trays should be placed:

  1. Flat and full of water
  2. Stacked inside each other
  3. On edge or inverted so water drains
  4. Wrapped tightly
Show answer
Answer: C. On edge or inverted so water drains
Prevents trapped condensate.

Report an error in this question

26. Which items can be damaged by steam?

  1. Stainless steel
  2. Glass bowls
  3. Metal trays
  4. Heat-sensitive plastics and some electronics
Show answer
Answer: D. Heat-sensitive plastics and some electronics
Check the IFU.

Report an error in this question

27. A pack that is too dense may fail because:

  1. It cools too fast
  2. It is too light
  3. Steam cannot reach the center
  4. It looks bad
Show answer
Answer: C. Steam cannot reach the center
Penetration is limited.

Report an error in this question

28. The chamber drain strainer should be:

  1. Removed
  2. Painted
  3. Never touched
  4. Cleaned daily
Show answer
Answer: D. Cleaned daily
A blocked drain harms air removal.

Report an error in this question

29. Door gaskets should be:

  1. Oiled with cooking oil
  2. Ignored
  3. Inspected for damage regularly
  4. Removed
Show answer
Answer: C. Inspected for damage regularly
A leak spoils the cycle.

Report an error in this question

30. Chamber cleaning agents should be:

  1. Only those the manufacturer approves
  2. Household cleaner
  3. Any acid
  4. Any bleach
Show answer
Answer: A. Only those the manufacturer approves
Wrong agents corrode.

Report an error in this question

Questions 31 to 40

31. A daily start-up routine includes:

  1. Skipping tests
  2. Chamber inspection and the air removal test
  3. Overloading
  4. Painting the door
Show answer
Answer: B. Chamber inspection and the air removal test
Per sterilizer type.

Report an error in this question

32. A cycle printout shows cycle number, date, temperature, time and:

  1. Pressure
  2. Room size
  3. Staff lunch
  4. Pack color
Show answer
Answer: A. Pressure
Physical monitoring record.

Report an error in this question

33. If an alarm sounds during exposure:

  1. Delete the printout
  2. Release the load
  3. Do not release the load and investigate
  4. Ignore it
Show answer
Answer: C. Do not release the load and investigate
The cycle may be invalid.

Report an error in this question

34. Hot loads should be cooled:

  1. Under a cold tap
  2. In a freezer
  3. To room temperature before handling
  4. By fanning wet cloths
Show answer
Answer: C. To room temperature before handling
Prevents condensation.

Report an error in this question

35. Touching hot packs with wet hands can:

  1. Seal them
  2. Dry them
  3. Draw moisture into the pack
  4. Sterilize them
Show answer
Answer: C. Draw moisture into the pack
Handle with dry hands.

Report an error in this question

36. Items should be loaded so steam can:

  1. Be blocked
  2. Escape
  3. Stay in one place
  4. Circulate freely around them
Show answer
Answer: D. Circulate freely around them
Leave space between packs.

Report an error in this question

37. Textile pack size is limited because:

  1. Steam must penetrate to the center
  2. Cloth is cheap
  3. Cloth is heavy
  4. Cloth is pretty
Show answer
Answer: A. Steam must penetrate to the center
Follow validated sizes.

Report an error in this question

38. Preventive maintenance of a sterilizer is done:

  1. On schedule by qualified technicians
  2. By anyone
  3. Never
  4. Only after a failure
Show answer
Answer: A. On schedule by qualified technicians
Keeps it safe.

Report an error in this question

39. A process challenge device contains:

  1. Only wax
  2. Only paper
  3. Only water
  4. A BI or indicator in a defined challenge
Show answer
Answer: D. A BI or indicator in a defined challenge
Represents the hardest-to-reach spot.

Report an error in this question

40. Before release the physical monitors must show:

  1. Parameters within the set limits
  2. Anything
  3. Only the date
  4. A blank page
Show answer
Answer: A. Parameters within the set limits
Parametric check.

Report an error in this question

Questions 41 to 50

41. Come-up time is:

  1. The time needed to dry the packs
  2. The time the chamber takes to reach temperature
  3. The time the load takes to cool down
  4. The time between two sterilizer cycles
Show answer
Answer: B. The time the chamber takes to reach temperature
Part of the cycle.

Report an error in this question

42. A steam-flush pressure-pulse cycle:

  1. Uses dry heat with a long hold time
  2. Removes air with steam flushes and pressure pulses
  3. Uses gas plasma at low temperature
  4. Relies on gravity displacement alone
Show answer
Answer: B. Removes air with steam flushes and pressure pulses
An air-removal alternative.

Report an error in this question

43. Gravity cycles are most suitable for:

  1. Simple, non-porous loads per the maker
  2. Dense textile packs always
  3. Electronics
  4. Liquids in sealed bottles
Show answer
Answer: A. Simple, non-porous loads per the maker
Check the cycle table.

Report an error in this question

44. Prevacuum cycles remove air better because:

  1. They use dry air
  2. Steam is colder
  3. They use no pressure
  4. A vacuum pulls air out before steam enters
Show answer
Answer: D. A vacuum pulls air out before steam enters
Better penetration.

Report an error in this question

45. Sterilizer logs should record:

  1. Only the weather
  2. Only the date
  3. Only the room
  4. Load contents, cycle and operator
Show answer
Answer: D. Load contents, cycle and operator
Traceability.

Report an error in this question

46. The chamber pressure is shown on the:

  1. Drain
  2. Pressure gauge
  3. Gasket
  4. Door
Show answer
Answer: B. Pressure gauge
Part of physical monitoring.

Report an error in this question

47. A door interlock prevents:

  1. Cleaning
  2. Starting any cycle
  3. Closing the door
  4. Opening while the chamber is pressurized
Show answer
Answer: D. Opening while the chamber is pressurized
Safety device.

Report an error in this question

48. A safety valve:

  1. Cools the load
  2. Dries items
  3. Adds steam
  4. Releases excess pressure
Show answer
Answer: D. Releases excess pressure
Protects the vessel.

Report an error in this question

49. After cooling, a load is checked for:

  1. Room temperature, light level and door position
  2. Pack color, tray count and wrap brand
  3. Operator name, shift time and cart number
  4. Dryness, indicator change and package integrity
Show answer
Answer: D. Dryness, indicator change and package integrity
Before release.

Report an error in this question

50. The coolest part of the chamber is usually near the:

  1. Drain
  2. Top shelf
  3. Light
  4. Door handle
Show answer
Answer: A. Drain
Cold spot testing uses it.

Report an error in this question

Questions 51 to 52

51. The chamber should be inspected for:

  1. Debris, rust and damage
  2. Colors
  3. Pictures
  4. Labels
Show answer
Answer: A. Debris, rust and damage
Daily check.

Report an error in this question

52. Overloading with heavy metal sets can cause:

  1. Wet packs from retained heat and condensation
  2. Dry packs from fast cooling
  3. Shorter cycles with colder loads
  4. Brighter instruments after the cycle
Show answer
Answer: A. Wet packs from retained heat and condensation
Respect weight limits.

Report an error in this question

Related chapters

Continue learning

CSSD interview questions Mock tests MCQ practice CSSD NABH checklist

Frequently asked questions

How many Steam Sterilization MCQs are available?

This page has 52 free MCQs on Steam Sterilization with answers and explanations. More are added over time.

Is Steam Sterilization practice free?

Yes. You can practice without login or payment.

Are these official CSSD exam questions?

No. They are original practice questions written for learning.