TDS – CSSD MCQ Questions and Study Notes

TDS (total dissolved solids) shows how much dissolved material is in water. Practice free CSSD MCQ questions on this topic below.

Take the TDS practice test All 45 chapters

Learning objectives

Study notes

TDS is the total of dissolved minerals and salts, shown in mg/L or ppm. A TDS meter gives a quick estimate and it follows conductivity closely. Lower TDS means purer water.

Important points

Key terms

TDS ppm TDS meter

Practice MCQs on TDS

Tap “Show answer” to check each answer and read the explanation. These practice questions are written for learning with AI assistance and may contain mistakes. Please report any error so it can be fixed.

Questions 1 to 10

1. TDS stands for:

  1. Treated drinking supply
  2. Total dissolved solids
  3. Total dirty soil
  4. Temperature data set
Show answer
Answer: B. Total dissolved solids
It measures dissolved matter.

Report an error in this question

2. TDS is usually measured in:

  1. mm
  2. mg/L or ppm
  3. psi
  4. kg
Show answer
Answer: B. mg/L or ppm
Parts per million.

Report an error in this question

3. A higher TDS means:

  1. More dissolved minerals
  2. Purer water
  3. Sterile water
  4. Softer water
Show answer
Answer: A. More dissolved minerals
Less pure water.

Report an error in this question

4. A quick estimate of TDS is given by a:

  1. Thermometer
  2. Stopwatch
  3. Barometer
  4. TDS meter
Show answer
Answer: D. TDS meter
Many meters read conductivity.

Report an error in this question

5. TDS is closely related to:

  1. Weight
  2. Conductivity
  3. Smell
  4. Color
Show answer
Answer: B. Conductivity
Ions carry current.

Report an error in this question

6. For critical rinse water TDS should be:

  1. Irrelevant
  2. As high as possible
  3. Same as tap
  4. As low as the equipment limits require
Show answer
Answer: D. As low as the equipment limits require
Follow the maker's limit.

Report an error in this question

7. 1 ppm is about the same as:

  1. 1 mg/L
  2. 1 kg/L
  3. 10 mg/L
  4. 1 g/mL
Show answer
Answer: A. 1 mg/L
Common TDS unit equivalence.

Report an error in this question

8. Measuring TDS at the point of use is useful because:

  1. Quality can change in pipes and tanks
  2. It changes color
  3. It is cheaper
  4. It saves meter batteries
Show answer
Answer: A. Quality can change in pipes and tanks
Check where water is used.

Report an error in this question

9. A TDS meter should be:

  1. Stored in water
  2. Never cleaned
  3. Used wet and dirty
  4. Calibrated as instructed
Show answer
Answer: D. Calibrated as instructed
Accuracy needs calibration.

Report an error in this question

10. TDS tells you:

  1. The bacteria count
  2. The pH
  3. The total amount, not which minerals
  4. The exact minerals
Show answer
Answer: C. The total amount, not which minerals
Further tests give details.

Report an error in this question

Questions 11 to 20

11. Low TDS means the water is:

  1. Hard and likely to leave scale
  2. Always sterile and free of endotoxin
  3. Always acidic and unsafe
  4. Low in dissolved solids but not necessarily sterile
Show answer
Answer: D. Low in dissolved solids but not necessarily sterile
TDS ignores microbes.

Report an error in this question

12. Compared with RO water, tap water TDS is usually:

  1. Higher
  2. Zero
  3. Identical
  4. Lower
Show answer
Answer: A. Higher
RO removes dissolved solids.

Report an error in this question

13. Temperature affects meter readings, so many meters:

  1. Explode
  2. Stop working
  3. Ignore it
  4. Compensate automatically
Show answer
Answer: D. Compensate automatically
Use temperature compensation.

Report an error in this question

14. A TDS that slowly rises over weeks suggests:

  1. Declining RO performance or exhausted resin
  2. A new membrane working well
  3. Colder feed water
  4. Better water quality over time
Show answer
Answer: A. Declining RO performance or exhausted resin
Time to service.

Report an error in this question

15. TDS limits for critical water are set by:

  1. The vendor's mood
  2. The weather
  3. Staff preference
  4. Standards and equipment makers
Show answer
Answer: D. Standards and equipment makers
Follow the documented limit.

Report an error in this question

16. Most TDS meters measure:

  1. Weight
  2. Pressure
  3. Color
  4. Conductivity and convert it
Show answer
Answer: D. Conductivity and convert it
An estimate of dissolved solids.

Report an error in this question

17. When sampling for TDS you should:

  1. Add salt
  2. Use a clean container rinsed with the sample
  3. Use a dirty cup
  4. Wait a week
Show answer
Answer: B. Use a clean container rinsed with the sample
Avoid contamination.

Report an error in this question

18. A TDS record should include:

  1. Only the date
  2. Only the value
  3. Date, time, location and value
  4. Nothing
Show answer
Answer: C. Date, time, location and value
Complete records help trends.

Report an error in this question

19. A sudden jump in TDS needs:

  1. A holiday
  2. A party
  3. No action
  4. An immediate check
Show answer
Answer: D. An immediate check
Find the cause fast.

Report an error in this question

20. TDS includes dissolved:

  1. Only gases
  2. Only sand
  3. Only oil
  4. Salts, minerals and metals
Show answer
Answer: D. Salts, minerals and metals
Anything dissolved counts.

Report an error in this question

Related chapters

Continue learning

CSSD interview questions Mock tests MCQ practice CSSD NABH checklist

Frequently asked questions

How many TDS MCQs are available?

This page has 20 free MCQs on TDS with answers and explanations. More are added over time.

Is TDS practice free?

Yes. You can practice without login or payment.

Are these official CSSD exam questions?

No. They are original practice questions written for learning.